Correctly formed between the lags for the pedagogy is the beginning of the process of engineering design. Today, there are a lot of forgetfuls in the zupiniai vibration on the stem of the tree pidlogi. The surface of natural material is rendered ecologically pure and aesthetically addictive. In a large number of ways for the establishment of the necessary and practical reversal, there are lags for the pedagogy. Planks and plywood are laid on them due to the peculiarities of the project. The number of materials may differ from the technical characteristics, which require a special approach to skin problems.

Lags are called bars, which are laid on the back of the prepared base. Such a basis can be a concrete slab, stoves or beams. Prepare logs from different tree species. In dry areas with low passage, a bar is placed from the yalin or pine. As soon as the operation of the room is tied from the very beginning, then more beautifully the timber is from the modrini. Regardless of the fact that at any given show, a lattice will be removed, it is necessary to choose a hydro-isolation. Naykrashche for ts'go go ruberoid. Before installing the wood, it is necessary to dry it well and coat it with an antiseptic.

For some vipadki, for clean claddings, sieve lattices with metal, plastic or zalizokonnyh stovpchikiv.


Yake praise the decision, choose the forgetful one, focus on your financial capabilities and skills.

Laying pidlog on logs and such perevagi:

  1. Improving the quality of the ratio, reducing its heat conductivity, reducing the sound insulation characteristics.
  2. Between the lags it is possible to expand the community, lay the heat insulating material. It can be positively identified on comfort and interiors.
  3. Rivnomirnogo navantazhennya to chornovu pidlogu, to improve the term of yogo service.
  4. Otrimannya ideal basis for financial pokrittya.

For the width of the timber, the lag can be made independently from the boards. The decal of the lamellas is glued together and tightened with screws. Some types of deformation occur due to fluctuations in volumetric flow.

Rozrakhunok pidlogi from boards


First, put the board down to the log, you need to make sure from the configuration of the timber for the log. The parameters of the later supports are to be laid out from the finish of the finishing coat and before the run along the support points. They vvazhayutsya beams and pіdpіrki, as they are put in front of the lags. If there are more such grains, the thinner the future of the timber will be.

When carrying out the construction work, follow up with such a reduction in the amount of time spent spilling and overriding the timber:

  • 200 cm - 100x50 mm;
  • 300 cm - 150x75 mm;
  • 400 cm - 180x100 mm;
  • 500 cm - 200x150 mm;
  • 600 cm - 220x175 mm.

Spіvvіdnoshennya side lag, scho ukladayuetsya, blame butti 1: 1.5. May the beam so that both sides were vertical.

So the most important indicator of the performance of the finished cross is the interval between the lags. The fault is so, that it is better not to bend under the load of 300 kg / m2. This is the norm for living entities. When the boards are 20 mm wide, the croc is 30 cm between the logs.

First, lay the cross from a bar and a lath, it is necessary to use the following rules:

  1. If we insulate that finish pokritty, a small gap between 3-5 mm is to blame. The necessary ventilation of the tree.
  2. The edges of the boards may be on the sides 3-6 mm from the walls. The price is necessary to expand the coverage for an hour, depending on the requirements.
  3. When the installation is carried out, dozіlno skin 100-150 cm in front of the bar, put the pіdpіrki. Їх it is possible to build up from the center or to formulate the sawn timber. Small drops in height are compensated by shmat ruberoid.

Vibrating material for logs, it is necessary to cup the timber with a supply of energy. Podibny zhid to allow not to interconnect the objects in the inter'er.

Foundations for plywood

They do not care about those who see the material as a high quality, their style up to the vigin and the clutch of the mensha, below the mass of the tree. You should take less time from plywood when working with plywood, less when robots with boards. As a rule, plywood is vicorized for storing chornovoy pidlogi. Linoleum, kilimi and stripes, parquet and engineering board are laid on the surface.

For robots, slіd kupuvati slabs zavtovshki not less than 12 mm. Yaksho pokrittya will be two-ball, can be covered with plywood with a thickness of 8 mm.

When designing the parameters of the lattice slid, they are used on the size of the plywood. At the budget shops you can add sheets with a format of 1525x1525 mm and 1220x2440 mm. When robots with slabs 1525x1525 mm, the lags are laid with a crocodile of 50 cm. If the pitch is single-ball, then the interval between the speed is up to 38 cm. If the frame is vibrated into coriander material with a format of 1220x2440 mm, then the frame is shunted on the side of 40 cm. Try to ensure that the edges of the leaves were transferred to the beams, and not at the older camp.

Oskіlki plywood, when fastened to the frame, can be curved to the finnial plywood, then the cupuvati slabs from the one-sided fillet. For storing the first ball, add some unpolished plywood. When carrying out maintenance work at the applicants due to the increase in the amount of money, it was necessary to change the level of water on the cinnamon material.

The plates are arranged in the check order. Before screwing them, they need to open the openings for the screws and chamfer them. The price is necessary in order that the plywood did not shake, and the droplets of the screws were inserted into the black plywood. Between sheets of material, it is necessary to fill a technological gap with a width of 2-3 mm. Pislya stacking of wines is scalded with mastic.