Most of the cars, having gathered enough information on the right, ask to independently carry out repairs and maintenance of their good horse, not going to the motor roads.

If you read this article, then, better for everything, there is one of these motorists. To fix a lot of highs from the area of ​​the vlasny garage to the necessary possessions, the first item on the list of necessary speeches є knights for the car.

Otzhe, you resigned yourself to your hands and build a self-made knight at the garage, and not buy it in a special equipment store. Tse zrozumіle bazhannya: the part of such a possession may not be much less for the part of your car, with all the vicissitudes it will be rather rare (only if you don’t get to drive a service station in the garage).

Idea vinikla, bazhannya tezh, now instructed hour vibrate the construction of the winged annex... For the whole varto, I will pay respect to the employees of the factory virobniztva, presented on the market for special conditions, "look" for the purpose and show that you can see how you can do it.

Shvidshe for everything, let's go to your eyes two-sided knight, which you can know practically at the leather motorway. This type of attachment can be equipped with an electro-mechanical or electro-hydraulic drive.

The first vipad in the middle of the skin stitches of the rip-off shaft, wrap it up with an electric motor with a gearbox. A nut is mounted on the riser shaft, so that it can be moved up and down as soon as possible, on which the car can be trimmed.

At the two-way electric The shaft is replaced by a hydraulic drive, the grip of which is flashed by an electric motor.

To run інші options for similar design, ale z one, three chotirma stiykami.

Another type of knight - knife De platform with a system of importance (which are called "knives") go down and go down behind the aid of hydraulic drives, which are driven by electric motors.

Adopting additional designs, you can get out of the way of power and problems that require revision. Nasamper, tse bezpeka robots- Nіkhto not bazhaє, but in one not even far away day, take away an important trauma, or a loss through a person who is angry.

To that, it was necessary to select the materials and the construction of the annex so that it was shown that the mass of the car was displayed, and from a solid stock.

Varto also podbati about the production of locking mechanisms., scho allow you to put the car on the road in late situations with a knight.

І the main problem, from which one can use a two-sided or two-sided knife-like device with his own hands - the folding of the preparation of that road parts. At home minds, the big riser shaft is practically unhappy, the cylinders and hydraulic hoses on the right are foldable, and the stink does not come off cheap.

More simple and simple attachments for the installation in the garage minds of the options of the auto-driver, which turns the car on a bik on a cut of 45-60 and ranks transfer... Zupinimosya on new and wonder, why and how it is possible to grow.

How can you make a pidyomnik near the garage with your own hands? Pidyomnik-transfer be stored in a number of parts: front stays, cherevika, maidanchiks, upper, lower and rear beams and other elements between them.

To prepare you the necessary steel sheets with a thickness of 4 mm, coils, bushings, fasteners and tools for cleaning, cutting and drilling metal.

The first stage of preparation transfer- Cherevik, to serve as a supporting surface for the jack. The shoe went through the steel sheet so, as it is shown on the armchair, at the same time it is very important to show the size of the "earbud", so that it walks up the hill and down the front stile.

Itself style to play from kutochkiv 32, up to 1500 mm, as they go to the "square" that will ring. We will need two such "squares", made by ourselves in small cocks, but it seems that the upper beam could move between "squares".

At the lower part of the hole to open for the support pipe, far away you need to open the hole in the singing prompts - the stench is necessary for the metal fingers, as to fix the shaft and the upper beam.

Another stage the opening of the transfer with your own hands - the opening of the central beam that maydanchik for her. The maidanchik climb from the steel sheet, the edge of which you need to bend, cut off the "box", or weld the "boxes" її sides to the crush.

Our vipadku has a dovzhin maidanchik 350, a width of 150, and a depth of 20 mm. All the middle of the "box" is followed by the vipilany behind the її dimensions of the shmatka of the tree; The gum is attached to the tree from above, from the bottom to the metal a weld is welded to the upper beam for fastening to the upper beam and the ribs of the rigidity - that's all, the maidan is ready.

One small plate is tightly welded with a small plate, until a bushing is fastened to its side for closing from the rear beam, until the last finish, weld directly for a jack and bushings for metal toe-feet.

Step croc- Removal of the rear beam, it is necessary for the vehicle to be fitted from the side, so that it can be thrown over. Dovzhina girders are guilty of being close to home cars, for that it is possible to take a chute of 32 to a length of 1500 mm, and to make two square profiles each.

In the middle of the rear beam, it is necessary to weld a complete vuzol to be prepared from sheet metal. It is necessary for making the rear, upper and lower beams between themselves.

Stop shy away from the square profile of metal cuts and to fasten to the rear beam and front stile. To get too hung up if you don't want your finger-stoppers, raise the jack and that's all - a self-propelled car driver, ready-made.

Chi is everything independent?

And what about robiti, what if bazhannya otrimaty a garage knight for a car є, hello an hour to get ready to go? For є o'clock, ale dumb required tools and a navichok, for you will be afraid that your design isn’t showcased.

In such a razі, the senses turn up to the additional fahіvtsіv., as you can change the transfer rate specially from your car and garage.

Corisne video

Until yours, respect a video about a car driver for a garage with your own hands.

Another video about a knight for a garage with your own hands.

Yak to kill a nad_yny knight at the garage with your own hands?

It is not easy for the owner of the garage to use his own hands to add a car crane to the repair of a transport vehicle. Most of the knights at the garage will build an auto-booth for an hour, the dimensions of the construction will be taken out of the area.

Who are the auto-users?

  • odnost_ykov_

it is possible to visit the specialized shops of the mobile type. A compact crane with a pre-built, portable mechanism, which does not take a lot of money, which is very important for a garage;

zavdyaki tsyu avtopidyomnik can be viconati be-yak slyusarnu robot. When constructing with damp hands, lift the height up to the crossbeams, between the bars;

  • hydraulic

the most widespread type of automobile crane. The unit is most often victorious to be the masters of transport means, there is a great deal of cost-effectiveness. At the same time, the master of the hair quilts for the wits of the line іf the glands;

rake and ratchet mechanism are interconnected, the support-important system is transferred. The building is equipped with a rail. A metal casing to clean the part from the mechanical blocking;

  • pneumatic

Yaksho, they decided to build a crane with their own hands in a garage of this type, with the robot, the pump was connected. Small wheels can be reached from the bottom of the jack to the bottom of the jack;

danish pidyomnik at the garage to be compact, stylish and efficient. However, in the middle of a short time, you can see a little amount of control, a slight amount of time and continuous control of development.

Self-made knight at the garage is ready to go to the car. Create with your own hands an attachment to garage Obviously, there is a lot to save money, and the design is to go on an individual basis. Vinahid is relevant for the middle of avtovolnikiv: self-study dvigun, for example, from transport, it’s unfortunate, you can help the robot front tap.

How can you create a superb garage builder?

The design is as follows: boom cantilever fastening, wrap around on a vertical shaft, on which to stand up from the might of the later collapse. The winch is secured for an additional bolt. The shaft is welded to the base, the steel plate is rigidly bolted to the insole fragment.

Strength to cook from steel coils, flasks, podkosu. The bottle has a bronze bushing yak bearing kovzannya.

Manual winch є main part avtopidyomnik near the garage. Completely buy ready-made virib.

Another listener vinakhid

It is possible to rotate a rack-and-pinion crane from the handheld devices.

Two houses at the end of the day garage the steel coils to be built in on the singing height. A steel plate with a worm gearbox is attached to the policemen, which is not fitted. The high mobility of the plate allows for the transportation of the vehicle over the engine.

The reducer can be used for large vantages. Zirochka put on and be pulled from the worm shaft with a key. The small diameter wedge is also attached to the output shaft of the gearbox and is secured with a key. It’s impossible to put a lance (at the slab, open it in the slab) on the star.

Yak exploit vityag at the garage. For example, pid dvigun car with your own hands loops are introduced, which are thrown on the hook. Then the shaft of the gearbox is wrapped and the power plant of the car is replaced.

Modernization

Installation of a pidyomnik in garages with electric motors with lowering gearboxes.

Self-made "transfer" of a car.

To prepare a knight, a necessary algorithm is needed.

For fixing the unit to the metal, a steel dart is welded. When the internal growths are dimmed, the cherevik is oversupplied without any problems.

Small pieces (15cm) are taken from the square behind the auxiliary clamps. A shear is inserted into one of the squares. The design is fixed with electric rivets. Vuzli vikhodyat rozbіrnogo type.

  1. The side of the Maidan.

The form is taken from the sheet material, the sides are bent, or a two-centimeter smug is welded onto a potholder for fastening a gummed board. At the bottom of the maydan, it’s the edge of the rigidity. On the upper beam there is a maidanchik, which is guilty of the mother of a light hid.

  1. Vuzol with a full back.

Mіzh two sheets of metal are welded around the perimeter of the steel smuga. The anterior fragment will become visible.

For the help of the clamp, climb and cut into a square, plan for all the design, open it in such a rank, so that it is easy to mark the metal fingers in front of the upper beam and the cherevik. By composing a square profile, it will be possible to connect all square modules (it is necessary to insert the rosettes between the profiles). The upper beam, as a result, is guilty of walking smoothly and between the profiles.

  1. Front vuzol

Marks in the center and along the edges are wrapped around the edges, then the material is formed into a P-shaped form, as it is wrapped on a metal haircut.

A metal insert is welded on one edge in the center, a plate is fastened on top, and the result is a rectangular shape profile. The insert of the ma buty has been prepared from the sides and is stolen. On the front part of the beam, a guide jack and a bushing with rollers are welded.

With a diameter of 1 cm, the metal rod will bend during the front heating.

The square profile has cuts. An M16 nut is fastened to one side, and it is welded in, from the other side an opening to a millimeter bolt is secured.

Winch with your own hands

The auto starter can be the basis for the self-winding winch opening. Maidanchik is located from standard sheet metal, to which all universities can be attached. On the platform, it was approved, to weld on the landing place for mounting to the drum shaft.

Then slide the gearbox, the part is welded in such a rank, the main shaft is visible uphill. The starter adapter is attached to the upper shaft of the gearbox. The module, teeth and gears are attached to the primary shaft. Carrying out is switched on, as only the starter is fixed.

The simplest pedestrian near the garage

Scrap, mіtsna mace abo montuvannya otvoryuє vіs. The detail is driven in at the ground. The part of the trumpet rides until the axle is trimmed, showing the function of the drum. Weide is a simple knight. On the pipe dialer, there is a whip rope attached to it, before inserting an important one. The Іnshy cable rope is attached to the transport system. It is possible to ascertain that a mechanism has appeared at the garage, and a passenger car has been taken out. I nigholovnіshe, wіn ruin with my own hands. Tse crane power construction. І zrobiti pіdyomny pristіy awkwardly.

Pid bags

Є the powerless possibilities of getting ready to get used to the garage buddies, and how to get rid of them if necessary. And such is the need to wait for the post before the technical inspection. Self-contained pidyomny attachment necessary for inspecting the bottom of the car, repairing the zones of the galvanized system, cardan, other universities and parts of the transmis.

Manually look around the steering wheel of the keruvannya, її fastening to the front wheels, makin that good operation. When the unit is open, it’s okay, the coristuvach will negate the more important mechanism with the smallest penny vitrates.

With your own hands

Automobiles may be the power of lamatis, inimayut periodical technical service like tech. Access to the lower part of the garage drain is often uncomfortable through the doorway of the building. If you need all the necessary tools, possessions and ready-to-robotics, you can change the replacement of the running gear, transmission, motor. Unimportant to those who fix the needs when repairing cars with their own hands, it is even dearly expensive to get them for the victorious at their needs. The technical service can be used not often twice in a row, so the units that the higher education institutions are more beautiful to use with their own hands.

Automotive knight for the garage

Yak tipi vityagiv

Drivers are aware of the most varied options available, which are based on the method of picking up the vehicle and the type of drive. For the repair of vehicles, three types of drives are the main ones:

  • lantsyugovi mechanisms;
  • gwint;
  • hydraulic systems.

The way to pick up a car is important for the design, garage knights can be used for fork, knife, or platform visitors. The most popular є forklift units, the basis of such єdovy shaft іfrom development instrumental steel. The details of the building assembly showcase the installation of an average-statistic car, it is practically unwise to build the mechanism with your own hands through the folding design of the saws.

Vidiomnikiv for car repair

With our own hands, it’s easy to get the knights of the platform design from the gwent mechanics.

Parallel to the laying of the beams, fastened to the mechanism, building a car weighing up to 3 tons.

Vibrating design

For the preparation of the unit for the motor transport, the power hand is important to understand the constructions that are presented to the market. The part of the finished possession can be adjusted to the price of the car. At motorways, it is possible to install the most popular option - a double-strut jack, the design can be a Viconan with a hydraulic or electric drive. The design can be built from the pre-existing beams, fallen from the pre-existing girders.
The knife pidyomnik has a platform, the collapse is guided by a mechanism similar to knives. Self-propelled knight of this type is brought to robotic mechanics by means of a hydraulic drive, connected to an electric motor. Before preparing such constructions, it is important not to forget about the technology of safety. With robotic details, the mimicry can go down, before being brought to non-gated inheritance. The self-employed automobile knight is guilty of being able to make preparations due to the reserve of strength or aggregate exertion, with the victorian it is important for the nobility of the masu of the element to grow up.

In case of late situations with a garage driver, you can use the locking mechanisms. To avoid critical moments, it is necessary to revise the electric motor and hoses. The main problem is the preparation of the gwent pidyomnik with his own hands, the folding and the preparation of the mechanism. The hydraulic parts are expensive, but the new design is not good enough.

For a garage drive to modify the mechanism, allowing you to drive the car from the side. With your own hands you can get a hydraulic lift, like a car on the road up to 60 degrees, such a design is called transfer.

Pidyomnik near the garage with your own hands

For a victorian in a garage, you can get a kit for a car with your own hands. Needed components, tools and wipers.

The self-made knight is ready to be prepared from the stagnation of the offensive details:

  • Steel coils with a size of 8x8x1 cm for making a stylish design.
  • Worm gear reducer. The new virib can be expensive, call to pick up on picks or know about the non-working mechanism. It will be necessary to respect the performance, the indicator to be repaired is 350 kg, the indicator of the transmission strength is 60 kg.
  • The slab is made of steel, with a minimum thickness of 1 cm, to be used from the old possession.
  • A set of bolts, a hook for fastening, dowels with the shape of a star.
  • A decal of large lancers with a diameter of lanoks of 2 cm. Weak lantsyugi do not show up on the job, so I respect the quality of the virob, because the materials can stretch out for the hour of the robot.
  • Steel rope 5 mm thick.

The formation and establishment of universities will be in accordance with the observance of the proprietary instructions. The fastening of steel cuts is seen on the walls of the anti-slip repairs from the hood of the car. A steel plate is placed on top of the cuts for the child with his own hands. Use the preparation bolts. Then it is necessary to install the worm gear, locking the key on the drive shaft. The key of a small diameter is installed on the output shaft of the gearbox.

Pidyomnik lantsyugovy with his own hands

Opening of the slabs, according to the diameter of the lancet, for the purpose of the installation of the lancet mechanism. It is important to come to respect the safety, at the frame, open the door through the pedestal, they insert the locking mechanism.

Features of the exploitation of such a knight

Vikoristannya with a worm-type robot unit is suitable for a car engine or non-load-bearing parts. The procedure for storing an avtopidyomnik, prepared with his own hands of simplicity, followed by such actions:

  • Dismantle the dvigun fasteners, bolts, nuts.
  • The idea is to connect the loops of the steel cable to the construction.
  • Wrapping the drive shaft go by way of sorting through the lance, with small zusillas it is possible to change the detail to the required position.

Pidyomnik at a worm-type garage

If you need to see a car from the zone and carry out robots, you need to send it to the engine. The delivery of any style can be done with your own hands, the design is guilty of but mitsnoy, you can display a great deal of new options. We turn it on with victorian є steel on wheels, allowing you to move the part at the necessary strings.

Yaksho car zanadto great

The repair of great cars is not bad, the size of the number and the height of the clearing may not be enough to take the necessary parts for the required height. The process is carried out by the assistant, which is a detail for the preparation of steel. The wrapping of the reducer is drawn with the opposite side to the installed element.

Autodirect for great cars

To create such situations to think about the reduction and modernization of the car knight for the garage with your own hands. I can get ready to crumble the structure, as we can get the chance to ruin a part, so that it’s necessary to come back. It is possible to install an aggregate installation with an electric motor on a lowering gearbox, at the same time it is possible to use a reference crane for large-sized mechanisms.

Transfer with your own hands

Transfer vikoristovuyutsya to pick up one from the side of the car to the required degree. A simple option, which is not in the presence of special attachments behind the butt of the gearbox and lantsyugiv.

Self-propelled transfer for cars

The process of transferring with your own hands includes a number of steps.

  1. The cherevik is ready for the robot at the viglyadi support the maybutny jack. We will carefully follow the preparation for the armchairs of the sizes, schob hid buv vilnym.
  2. The style is for the person to be able to use the squares up to 1.5 meters, folding up to the shape of the squares, mounted with the appliance. The strikes are victorious at a number of two pieces, it is important to see it, through the yak there is a beam.
  3. Open the vysverdlyuyutsya for fastening the support tube, as well as the necessary locking mechanism.
  4. The maidan for the beam is prepared from a sheet of steel, the edges become bent, and the result is a box, before which the sides are welded.
  5. Pidtrimka of the car from the protolezhnyh on the sides go by the way, prepared with your own hands, the constructions of the beams. The square profile is designed to fit into the car.

For an hour every day, you can turn up to the fahivts, as they prepare the mechanism of transferring to the garage as soon as possible.

Simple pocket for turning the car

For a victorian in an open space, you can create a simple paver for turning a car. The running part of the auto maintenance service will be repaired in a timely manner, for the duration of the outbuilding, it is unfortunate that the robots will be zupineni.

The stagnation of the mini-driver in the garage is due to the increase in the number of people, the result of which may be the increase in the number of cars. It is not enough to get in trouble for repairing a car with a strong cut, because there is no way to get out of the way. Vigotoviti can be done with a wicket way through the rope mechanism from the old winch.

Problems with the preparation of the student

Part of the autotune in the ready-made viglyadi visok, protesting with your own hands, the options can be sent to the person who is right for him, if the design is not correct. Vaga of a car is not to blame for overturning more than a ton, with a fall in the design on a person, it is possible to reject nonvolatile injuries.

Self-made knight for a car to be ready for the preparation of armchairs, or vikoristovuyutsya version of ready-made virobes. For the remainder of the vipadku bring the visoki to the calculation of the author's tips. Incorrect distribution of the basis of one of the squeaky universities can lead to non-earthed herds, with a short drop, the unit can get lost.

For a self-made kit, prepared with his own hands, it is not a matter of getting to know the details of that university, without them. You can know this kind of accessories at great stores with the implementation of alarm technology. Whenever there is a need for new parts, it is not enough to have a virus on the puncture point of the receiving metalwork and enterprises, which write off old parts.

Yaksho vi knew the mercy, be weasel, see a fragment of the text and natisnit Ctrl + Enter.

Spilnoti ›Garage Mriї› Blog ›Pidyomnik for the garage with your own hands.

Pidyomnik of holes, preparation from hand-held materials. The following materials were used to prepare the student for the vicorists.
Channel 100 mm.
Kutnik 50 mm.
Kutnik 63 mm.
Jack vikoristovuvavsya 12 tons.
Profiled pipe with a diameter of 50 and 40 mm.
Everything was brewed by arched zvaryuvannyam.
At mісce kolіs vikoristovuvav the timing rollers.
The report information is in the video clips.
I recommend you twice manually for an hour of robots.